Brake Pad Replacement: When to Replace and How to Replace
Brake pads are wear-and-tear parts. With the increase of service time and braking times, their friction material layer will gradually wear down. When the wear reaches a certain level, they must be replaced in a timely manner; otherwise, the braking effect will be affected, and even safety accidents may occur. So, how do we judge when brake pads need to be replaced?
When to Replace Brake Pads
Check the Thickness of Brake Pads: This is the most direct and effective way to determine if brake pads need replacement. Generally, the thickness of the friction material layer of new brake pads is about 10-15 mm. When the wear reduces it to 3-5 mm, replacement should be considered; if the wear drops below 2 mm, immediate replacement is a must. At this point, the braking performance of the brake pads has significantly declined, and there may even be cases where the backing plate of the brake pad directly rubs against the brake disc. This will not only damage the brake disc but also lead to brake failure, endangering driving safety. We can directly check the thickness of the brake pads through the gap of the wheel hub. If the view is unclear, the tire can also be removed for inspection.
Listen for Brake Noise: Many brake pads are designed with a wear warning plate (a metal plate) in their friction material layer. When the brake pads are worn to a certain extent, the wear warning plate will come into contact with the brake disc, producing a sharp "squeaking" or "chirping" noise during braking. If such abnormal noise is heard during braking and persists, it usually means the brake pads are worn to the extent that replacement is needed. However, it should be noted that sometimes foreign objects (such as small stones, dust, etc.) on the surface of the brake disc can also cause noise during braking. This kind of noise is usually intermittent and will disappear after the foreign objects are cleaned, so careful distinction is required.

Feel the Braking Effect: If during driving, you notice that the stroke of the brake pedal becomes longer (it feels softer when pressed), the braking response slows down, the braking distance increases significantly, or the vehicle deviates or shakes during braking, it may be due to severe wear of the brake pads or other issues. In such cases, you should promptly go to a professional maintenance institution for inspection to determine if the brake pads need to be replaced.
Check the Dashboard Warning Light: Many modern cars are equipped with a brake pad wear warning system. When the brake pads are worn to a certain degree, the brake pad warning light on the dashboard will turn on, reminding the driver to replace the brake pads in a timely manner. If the warning light is on, arrangements for replacement should be made as soon as possible, and it should not be ignored.
How to Replace Brake Pads
When it is confirmed that the brake pads need to be replaced, it is recommended to choose a regular auto repair shop or 4S shop, and have professional technicians perform the replacement. The specific steps for replacing brake pads are roughly as follows:
Preparation Work: Park the vehicle on a flat and solid surface, pull the handbrake tightly, and place wheel chocks to ensure the vehicle is stable. Then open the hood, check the level of the brake fluid. If brake pad replacement is needed, it may be necessary to draw out some brake fluid first to prevent the brake fluid from overflowing during the installation process.
Remove the Tire: Use a jack to lift the vehicle, ensuring the jack is supported at the vehicle's designated position, then remove the tire where the brake pads need to be replaced.
Remove the Brake Caliper: Locate the brake caliper. Usually, the brake caliper is fixed by two bolts. Use an appropriate wrench to unscrew the bolts, then remove the brake caliper from the brake disc. It should be noted that after removing the brake caliper, do not hang it randomly to avoid damaging the brake pipeline; it can be fixed at a proper position on the vehicle body with iron wire or rope.
Replace the Brake Pads: Take out the old brake pads from the brake caliper, then clean the dust and impurities inside the brake caliper, and check if the piston of the brake caliper is in normal condition. Next, install the new brake pads into the brake caliper, ensuring the installation direction of the brake pads is correct (usually, there is an installation direction mark on the brake pads).

Reset the Brake Caliper: Reinstall the brake caliper with the new brake pads onto the brake disc, and tighten the fixing bolts. Note that the tightening torque of the bolts must comply with the vehicle manufacturer's regulations to avoid being too loose or too tight. Before installing the brake caliper, it may be necessary to push the piston of the brake caliper back to its original position to accommodate the new brake pads. At this time, a dedicated piston reset tool can be used, or a wrench and other tools can be used to gently push the piston back.
Install the Tire: Reinstall the tire onto the wheel hub, tighten the tire bolts, then slowly lower the vehicle, and remove the jack and wheel chocks.
Test the Braking Effect: After replacing the brake pads, do not drive at high speed immediately. First, conduct several braking tests in an open area to feel if the stroke of the brake pedal and the braking effect are normal, and check if there is abnormal noise or vibration during braking. At the same time, it should be noted that a certain running-in period is required between the new brake pads and the brake disc. During the running-in period (usually 200-300 kilometers), sudden braking and heavy braking should be avoided, and smooth braking should be maintained as much as possible to ensure that the brake pads and brake disc can fit fully and achieve the best braking effect.






